Closeouts

Lee .324 Bullet Sizer & Punch sizes cast bullets, also seats and crimps gas checks.

Click here to view parts

Lee 38 Super/38 ACP Carbide Factory Crimp Die sizes the cartridge while being crimped so every round will positively chamber freely with factory like dependability. This die applies a taper crimp. The adjusting screw quickly and easily sets the desired amount of crimp. Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered. A firm crimp is essential for dependable and accurate ammunition, as it eliminates the problems of poor ignition of slow burning magnum powders.

308 Winchester Quick Trim Die

Use Quick Trim die in conjunction with the Deluxe Quick Trim Case Trimmer or Deluxe Power Quick Trim.

Click here to view parts

Lee 45 ACP Pistol Breech Lock 3-Die Set includes colored Smart Lock bushings for easy die identification, Carbide Full Length Sizing Die, Powder Through Expanding Die, Bullet Seating Die, Universal Shell Holder, Powder Dipper and Instructions/Load Data. Select this die set if you are reloading mixed range brass and have the Breech Lock Quick Change feature on your reloading press.

Click here to view parts

Lee 44 Special / 44 Magnum Pistol Breech Lock 3-Die Set includes colored Smart Lock bushings for easy die identification, Carbide Full Length Sizing Die, Powder Through Expanding Die, Bullet Seating Die, Universal Shell Holder, Powder Dipper and Instructions/Load Data for both the 44 Special and 44 Magnum. Select this die set if you are reloading mixed range brass and have the Breech Lock Quick Change feature on your reloading press.

Note: These dies can be used to reload the 44 Magnum and 445 Super Mag. 44 Magnum reloading data may be purchased here, 445 Super Magnum load data would need to be obtained from your favorite powder manufacturer.

Click here to view parts

Lee 38 Special | 357 Magnum Pistol 4-Die Set. Includes Carbide Full Length Sizing Die, Bullet Seating Die, Powder Thru Expanding Die, Carbide Factory Crimp Die, Universal Shell Holder, Powder Dipper and Instructions/Load Data for 38 Special and 357 Magnum.

Note:  You may use the 38 Special die set to reload for the 357 Magnum and 357 Maximum. You would have to back out the Powder Thru Expander Die, and the Bullet Seating and Crimping Die about 2 turns to compensate for the longer 357 Magnum case, additional adjustments needed for 357 Maximum. Load data for the 357 Max is available in Modern Reloading.

Click here to view parts

Lee 223 Remington or 223 Ackley Improved neck sizing die uses a steel collet to squeeze fired case to a precision mandrel, creating a precisely aligned case neck while reducing run out. Results in best accuracy and extended case life. Sizes just the neck and requires no case lubrication. Recommended for cases that have been fired through your firearm only.

Undersized flash hole decap mandrel sold separately.

.002" undersize mandrel sold separately

Lee Double Cavity Mold produces a no lube groove .452 diameter 230 grain round nose bullet suitable for 45 ACP.

There are no lube grooves, this bullet is designed to be used with powder coat or equivalent coating rather than Lee Liquid Alox.

Handles included.

Bullet Overall Length = .650 inches.

See our tips on powder coating.

Lee Double Cavity Mold produces a no lube groove .358 diameter 130 grain round with flat nose bullet suitable for cartridges like 38 Special, 38 Smith & Wesson, 357 Magnum, etc.

There are no lube grooves, this bullet is designed to be used with powder coat or equivalent coating rather than Lee Liqud Alox.

Handles included.

Bullet Overall Length = .525 inches.

See our tips on powder coating.

Lee Double Cavity Mold produces a no lube groove .356 diameter 115 grain 2 ogive radius nose bullet suitable for 9mm Luger.

There are no lube grooves, this bullet is designed to be used with powder coat or equivalent coating rather than Lee Liquid Alox.

Handles included.

Bullet Overall Length = .518 inches.

See our tips on powder coating.

The easiest, most convenient bench mounted priming tool on the market. Symmetrical design allows effortless right or left hand operation. Comfortable lever with just the right amount of mechanical advantage effortlessly seats even the most difficult primers with just finger pressure. The perfect mechanical advantage to feel the primer seating completely home into the primer pocket. Includes 1 small, 1 large and 1 folding priming tray.

Lee 9.3x72R Factory Crimp Die crimps the bullet in place more firmly than any other tool. Tests demonstrate that even bullets which have no crimp groove will shoot more accurately. A firm crimp improves accuracy because pressure must build to a higher level before the bullet begins to move. This higher start pressure insures a more uniform pressure curve and less velocity variation.

Lee 351 Winchester Self Loading WSL Factory Crimp Die crimps the bullet in place more firmly than any other tool. Tests demonstrate that even bullets which have no crimp groove will shoot more accurately. A firm crimp improves accuracy because pressure must build to a higher level before the bullet begins to move. This higher start pressure insures a more uniform pressure curve and less velocity variation.

Click here to view parts

7mm Express / 280 Remington Rifle Steel Full Length Sizing Die Complete.

Click here to view parts

Reloading brass with undersized flash hole? Undersize flash hole easy x expander is available as an accessory.