Custom Factory Crimp Dies

Custom Overrun Factory Crimp Dies Available for Immediate Shipment:

CARTRIDGE   CARTRIDGE   CARTRIDGE
17 Remington Fireball   375 Win. Short Mag   6.5 x 65R RWS
17 Remington   375 Weatherby Mag   6.5 x 68mm
219 Zipper   38-56 WCF   6.5 x 50 Japanese Arisaka
22 Nosler   401 WSL   6.5 x 284
22 Savage       7.35 Carcano
221 Fireball   41 Mag   7.62 x 40 WT
222 Remington Mag   416 Ruger
  7mm Weatherby Mag
240 Weatherby Mag   416 Taylor   7mm WSM
257 Weatherby   425 Westley Richards   8 x 33mm
257 Weatherby Mag   44 Auto Mag   8 x 56R
26 Nosler   45 Blaser   8 x 58R
28 Nosler   45-70 LeverRevolution   8 x 60 S
    45-90 Sharps   8 x 68 S
277 Wolverine   450 Bushmaster   8.5 Messner Mag
284 Winchester   457 WWG   8.5 x 63 REB
30 Herrett   458 African Express (2.653" case length)   8.15 x 46 R Schuetzen
30/338   458 African Express (3.000" case length)   9.3 x 64
300 H&H   458 Belted Express   9.3 x 72R
300 Rem SAUM   458 Lott   9.3 x 74R
308 Norma Mag   480 Ruger   10.75 x 68R
30R Blaser   50 Alaskan    
32 Remington   50 Beowulf    
32-40 Winchester   50-70    
    510 Kodiak Express    
33 Winchester   510 R Express    
325 WSM   6 x 62    
    6 x 45mm    
358 Hoosier   6mm BR Rem or Norma    
338 Blaser Magnum   6mm Musgrave    
338 Whisper   6mm PPC    
357 Herrett   6.5 Carcano   LARGE SERIES 1 1/4x12 THREAD
357 Maximum   6.5mm Norma   * 378 Weatherby Mag
358 Norma Mag   6.5mm PPC   * 450 Rigby Rimless
358 Yeti   6.5 x 54 Mauser   * 500 Jeffery
375 Blaser Mag   6.5 x 43   * 8.5 Messner Mag
375 Rem. Ultra Mag   6.5 x 47 Lapua    
375 Socom
  6.5 x 57 R   * Requires Classic Cast Press

Place your order here for the above custom-over-runs.

For sizes not listed, if you wish to order online, contact us so we can advise if the size you are looking for can be made, we will then give you the ordering link.

Unable to make the following cartridges:

  • 22 Rem Jet (too short)
  • 32 S&W Short
  • 38 S&W
  • 41 Long Colt
  • 257 Winchester Magnum
  • 460 S&W (you can use the # 90865 Carbide Factory Crimp Die for this cartridge to apply a Factory Crimp and post-size part of the case)
  • 475 Linebaugh
  • 480 Ruger
  • 50 AE (case diameter is too large to fit in the 7/8-14 die and too short for large series as a collet type crimp die. It can not be made as a carbide crimp die because the carbide would end up being too thin to have the necessary strength. If you wish to separate the bullet seating and crimping steps then purchasing a separate seating die body is your best option.)
  • 7.62 Model 1895 Russian Nagant Revolver
  • 56/60 Spencer
  • 500 S&W (use the # 90931 Collet Style Factory Crimp Die)
  • 8mm Nambu

Rifle Factory Crimp Die 7/8 x 14" thread

The collet-type Factory crimp die can be made for a wide variety of cartridges. Most cartridges will fit into the 7/8x14 thread die body.

If your cartridge falls within the following parameters it will fit the standard 7/8 x 14 die:

  • Bullet diameter .172 - .501 (minimum - maximum)
  • Body diameter .295 - .585
  • Case length 1.285 - 2.850 (All dimensions in inches)

Cartridges over the maximum in any of the three parameters will most likely fit into the large series die. These have a 1 1/4x12 thread, so your press must be capable of accepting this thread size. 

We need:

  • Payment of $25.00 + shipping
  • Dummy cartridge (a bullet seated in an empty case). The dummy cartridge is for testing purposes, so make sure it is within normal dimensional tolerances.
  • Any handgun case that is of a bottleneck design qualifies because the die would have to be made much like the rifle factory crimp dies but we do not make die bodies shorter than that you would find on a .223 Remington. Examples would be the 30 Mauser, 7.62 x 25 and the .357 Sig. The 50 AE also applies because the case is too short for the die bodies available.

Rifle Large Series Factory Crimp Dies 1 1/4 x 12" thread

Note that these Large Series Dies will only fit into our Classic Cast press, and some competitor's larger presses.

Large Series dimensions are:

  • Bullet diameter .300 - .577 (minimum - maximum)
  • Body diameter .575 - .875
  • Case Length 1.500 - 4.000 


We need:

  • Payment of $75.00 + shipping
  • Dummy cartridge (a bullet seated in an empty case). The dummy cartridge is for testing purposes, so make sure it is within normal dimensional tolerances.

Handgun Bottleneck Crimp Die 7/8 x 14" thread

Incorporates a collet to apply a rifle type crimp to the case. Makes these very difficult to crimp cartridges a delight to reload. Bullets do not need a crimp groove, as the collet is so powerful it will form one. 

Following cartridges can be made: 9x22 Major, 40 Super, 9x25 Dillon, 440 Cor Bon

Current lead time is 8 weeks.

We need:  

  • Payment of $40.00 + shipping
  • Dummy cartridge (a bullet seated in an empty case). The dummy cartridge is for testing purposes, so make sure it is within normal dimensional tolerances.


Handgun Carbide Factory Crimp Dies

For handgun cartridges can be made for most handgun cartridges that are not in regular stock. Sizes available run from 25 ACP sized cases up to the 45 Gap. 

Case length cannot exceed 1.375 inches

We need:

  • Payment of $30.00 + shipping
  • Dummy cartridge (a bullet seated in an empty case). The dummy cartridge is for testing purposes, so make sure it is within normal dimensional tolerances. 

Handgun Collet Style Factory Crimp Die 

We can make custom Collet Style Factory Crimp Dies for the following pistol calibers:

  • 41 Magnum
  • 475 Linebaugh
  • 480 Ruger

Minimum case length must be 1.285".
Maximum bullet diameter is .501".

Please check our Lee Collet Style Factory Crimp Die page for availability of additional calibers.

We need:

  • Payment of $25.00 + shipping
  • Dummy cartridge (a bullet seated in an empty case). The dummy cartridge is for testing purposes, so make sure it is within normal dimensional tolerances.

Products

Custom Rifle Factory Crimp Die 7/8 x 14" thread

SKU: 90595-custom

Custom Rifle Factory Crimp Die 7/8 x 14" thread
MSRP: $25.00

Quantity